App connected2 panels
Hard-sided tool box that locks into the grid. Unlock from your phone, get a ping if it moves.
Modular truck bed systemGet your
Get your
truck dialed.
The modular floor for your truck bed. Lock gear where you put it, change the layout in seconds, and pull the whole load to the tailgate.
- No drilling
- Sets up in minutes
- Fits full-size and midsize beds
- Pulls to the tailgate
The truck kit.
One kit, sized to your bed. Panels, fit strips, the ramp handle and a six-piece accessory starter set. Pick your truck and the price follows.
Modular truck bed system
DIALED Truck Kit
From $399
Midsize $399 · Full-size $499 · Long bed $599
- Main panels sized to your bed
- Fit strips for the walls
- Ramp handle
- 6-piece accessory starter set
Your truckKit sizes to your bed
Select your truck
-
Fit guaranteed
Sized to the truck you picked. Wrong fit comes back on us. -
Free shipping
Every kit, lower 48. -
No drilling
Sets up in minutes, no tools. - Secure checkout
Why a floor
Drawers take your bed. Racks take your sky. DIALED takes an inch.
12×12
Inch panels, one size. The floor is the same module whether your bed is five feet or eight.
16
Receivers per panel. Posts, dividers and tie points drop in anywhere and stay put.
0
Holes drilled. The floor sits on the bed, interlocks into one piece, and comes out with you.
How it works.
Full system breakdown →Lay the floor.
Panels interlock edge to edge from the bulkhead to the tailgate. Fit strips take up the width to the wall. No drilling, no frame, no lost bed height.
Dial it in.
Sixteen receivers per panel. Drop in a post, a divider or a tie point exactly where the load needs it. Move it when the load changes.
Pull it to you.
Grab the handle edge and bring the whole floor, and everything on it, to the open tailgate. Load from the ground, not from your knees.
See it work.
Floor in, gear locked, pulled to the tailgate. Ninety seconds, one truck.
Set up your way.
Same floor, different week. Move a few posts and the truck is set for whatever's next.
Accessories
Locks to the grid.
Every accessory drops into the same receivers as the starter set. Buy one now, it fits the next truck too.
Locks to grid2 panels
Hard cooler with a receiver footprint. Rides where you put it, slides out with the floor.
Stackable1 panel
Footprint matched to one panel. Stacks, latches, drops into the grid.
Tie-down4 panels
Hooks sized to the receivers. Cinch to the floor, not the bed rail.
Mount1 panel
Receiver plates for the racks, mounts and gear you already own.
Mount1 panel
Upright tubes that drop into any receiver. Rods ride locked and apart.
Locking3 panels
Padded, locking cradles. Secure in the bed, out in seconds.
About
Built from the tailgate back.
DIALED started with a bed full of sliding gear and a drawer system that cost the whole bed to fix it. So we built a floor instead: one panel, one grid, nothing drilled. Everything we make has to lock into it.
Designed and tested in our own trucks. Shipped from the lower 48.
Will it fit my truck?
Kits are sized by make, model, year and bed length for full-size and midsize trucks. Use Find my kit; fitment is confirmed again at checkout.
Does it need drilling or tools?
No. The floor sits on the bed and the panels interlock with each other. Fit strips take up the width to the walls. Accessories drop into the receivers by hand.
Does it work with a bed liner or tonneau cover?
Yes. The floor sits on spray-in or drop-in liners and under tonneau covers and caps.
How does the floor stay put?
Panels interlock into one continuous floor and fit strips close the gap to the bed walls, so there is nowhere for it to go.
Can I add or move things later?
That is the point. One module size and one receiver grid mean panels and accessories you buy later fit the ones you have now, in this truck or the next.
What if it does not fit?
Send it back. If your kit does not fit the truck you ordered it for, we take it back and make it right.
Your truck. Dialed.
Pick your truck, size the floor, and build the layout you actually need.
